Manufacturer: SOUNDLIGHTLED POWERHORSEBest suited for installation in electrical power distribution cabinets: 3 absolute high power outputs in just 4 installation slots (width units). The decoder can supply up to 600 watts of power using a 24VDC supply. The 3613PWM-H can drive all constant voltage (CV) LED modules and LED assemblies of any type and make.Common features are same voltage (12VDC or 24VDC will work), and common anode wiring topology (common „+“ used for all LEDs). The eye-friendly dimming results from high output frequency (244 Hz used), high output resolution (12 bit dimming), and a quasi-logarithmit output curve, which matches the human eye’s sensitivity.Combined with excellent DMX performance thanks to special SLR receiver chips to guarantee extended noise immunity and improved signal reception, full administration and monitoring capabilities due to advanced DMX RDM technology and lots of user configuration options, the 3613PWM-H will undoubtedly be your best choice to drive CV LEDs – we’re sure!Specifications DMX LED Driver 3613PWM-H5DMX PWM DRIVER for voltage controlled LEDs3-channelDMX512/1990, DMX512-A, DIN56930-2, DMX RDMDMX input fed-thruOperating voltage: 5VDC4 outputs 0…+12(24)V, max. 8A per outputTopology: Common AnodeDimensions: DIN Rail, 4 units widthANSI E1-20 DMX RDM V1.0 compatible4 DMX PersonalitiesPower supply monitoring, DMX RDM readableEye-friendly quasi-logarithmic curve3 output frequencies selectableOutput linear or quasi-logarithmicOutput smoothing: 3 characteristics selectableRDM Identify, Password, HOLD-LevelSlot-Labels and Device Label can be editedseveral additional RDM functionsYou can configure the interface via DMX RDM. Alternatively, the DMX start address, DMX personality and DMX HOLD mode can be configured using a start address board 3000P, 3003P, 3005P or 3006P. Start address boards can be used for all of our products. They must be purchased separately.

Manufacturer: SOUNDLIGHTLED POWERHORSEBest suited for installation in electrical power distribution cabinets: 3 absolute high power outputs in just 4 installation slots (width units). The decoder can supply up to 600 watts of power using a 24VDC supply. The 3613PWM-H can drive all constant voltage (CV) LED modules and LED assemblies of any type and make.Common features are same voltage (12VDC or 24VDC will work), and common anode wiring topology (common „+“ used for all LEDs). The eye-friendly dimming results from high output frequency (244 Hz used), high output resolution (12 bit dimming), and a quasi-logarithmit output curve, which matches the human eye’s sensitivity.Combined with excellent DMX performance thanks to special SLR receiver chips to guarantee extended noise immunity and improved signal reception, full administration and monitoring capabilities due to advanced DMX RDM technology and lots of user configuration options, the 3613PWM-H will undoubtedly be your best choice to drive CV LEDs – we’re sure!Specifications DMX LED Driver 3613PWM-HDMX PWM DRIVER for voltage controlled LEDs3-channelDMX512/1990, DMX512-A, DIN56930-2, DMX RDMDMX input fed-thruOperating voltage: 12…24VDC4 outputs 0…+12(24)V, max. 8A per outputTopology: Common AnodeDimensions: DIN Rail, 4 units widthANSI E1-20 DMX RDM V1.0 compatible4 DMX PersonalitiesPower supply monitoring, DMX RDM readableEye-friendly quasi-logarithmic curve3 output frequencies selectableOutput linear or quasi-logarithmicOutput smoothing: 3 characteristics selectableRDM Identify, Password, HOLD-LevelSlot-Labels and Device Label can be editedseveral additional RDM functionsYou can configure the interface via DMX RDM. Alternatively, the DMX start address, DMX personality and DMX HOLD mode can be configured using a start address board 3000P, 3003P, 3005P or 3006P. Start address boards can be used for all of our products. They must be purchased separately.

LED POWERHORSEBest suited for installation in electrical power distribution cabinets: 4 high power outputs in just 4 installation slots (width units). The decoder can supply up to 300 watts of power using a 24VDC supply. The 3604PWM-H can drive all constant voltage (CV) LED modules and LED assemblies of any type and make. Common features are same voltage (12VDC or 24VDC will work), and common anode wiring topology (common „+“ used for all LEDs). The eye-friendly dimming results from high output frequency (244 Hz used), high output resolution (12 bit dimming), and a quasi-logarithmit output curve, which matches the human eye’s sensitivity. Combined with excellent DMX performance thanks to special SLR receiver chips to guarantee extended noise immunity and improved signal reception, full administration and monitoring capabilities due to advanced DMX RDM technology and lots of user configuration options, the 3604PWM-H will be undoubtedly be your best choice to drive CV LEDs – we’re sure! Specifications DMX LED Driver 3604PWM-HDMX PWM DRIVER for voltage controlled LEDs4-channelDMX512/1990, DMX512-A, DIN56930-2, DMX RDMDMX input fed-thruOperating voltage: 12…24VDC4 outputs 0…+12(24)V, max. 3A per outputTopology: Common AnodeDimensions: DIN Rail, 4 units widthANSI E1-20 DMX RDM V1.0 compatible4 DMX PersonalitiesPower supply monitoring, DMX RDM readableEye-friendly quasi-logarithmic curve3 output frequencies selectableOutput linear or quasi-logarithmicOutput smoothing: 3 characteristics selectableRDM Identify, Password, HOLD-LevelSlot-Labels and Device Label can be editedseveral additional RDM functionsYou can configure the interface via DMX RDM. Alternatively, the DMX start address, DMX personality and DMX HOLD mode can be configured using a start address board 3000P, 3003P, 3005P or 3006P. Start address boards can be used for all of our products. They must be purchased separately.

LED POWERHORSE The DMX PWM Decoder drives voltage controlled LEDs (CV) and features four outputs max. 24V/2A each (Common Anode). The power supply is 24VDC (operating range 9...24V) and the interface can be configured to SMOOTH mode for soft dimming. Dimensions: 7 x 7 cm, DMX connectors (5pin Neutrik XLR) onboard.

LED POWERHORSEBest suited for installation in electrical power distribution cabinets: 3 absolute high power outputs in just 4 installation slots (width units). The decoder can supply up to 300 watts of power using a 24VDC supply. The 3633PWM-H can drive all constant voltage (CV) LED modules and LED assemblies of any type and make. Common features are same voltage (12VDC or 24VDC will work), and common cathode wiring topology (common „-“ used for all LEDs). The eye-friendly dimming results from high output frequency (244 Hz used), high output resolution (12 bit dimming), and a quasi-logarithmit output curve, which matches the human eye’s sensitivity. Combined with excellent DMX performance thanks to special SLR receiver chips to guarantee extended noise immunity and improved signal reception, full administration and monitoring capabilities due to advanced DMX RDM technology and lots of user configuration options, the 3633PWM-H will undoubtedly be your best choice to drive CV LEDs – we’re sure!Specifications DMX LED Driver 3633PWM-HDMX PWM DRIVER for voltage controlled LEDs3-channelDMX512/1990, DMX512-A, DIN56930-2, DMX RDMDMX input fed-thruOperating voltage: 12…24VDC3 outputs 0…+12(24)V, max. 4A per outputTopology: Common CathodeDimensions: DIN Rail, 4 units widthANSI E1-20 DMX RDM V1.0 compatible4 DMX PersonalitiesPower supply monitoring, DMX RDM readableEye-friendly quasi-logarithmic curve3 output frequencies selectableOutput linear or quasi-logarithmicOutput smoothing: 3 characteristics selectableRDM Identify, Password protection, HOLD-LevelSlot-Labels and Device Label can be editedseveral additional RDM functionsYou can configure the interface via DMX RDM. Alternatively, the DMX start address, DMX personality and DMX HOLD mode can be configured using a start address board 3000P, 3003P, 3005P or 3006P. Start address boards can be used for all of our products. They must be purchased separately.

The best warmwhite / coldwhite driverHardly to believe: 4 control channels on just 70mm x 70mm area, including DMX IN/OUT XLR connectors onboard! Up to 200W power (4x 50W) at 24VDC power supply, enough for demanding applications. The 3644PWM-EP is best suited to drive all types of voltage controlled LED assemblies, e.g. LED tapes, LED arrays or LED tubes. Common characteristics are common anode power supply (common "+"). The high-speed PWM output (selectable from 244Hz to 15,6 kHz) and the quasi-logarithmic intensity characteristic ensure best performance for all applications, including HDTV and other demanding jobs. Combined with excellent DMX performance thanks to special SLR receiver chips to guarantee extended noise immunity and improved signal reception, full administration and monitoring capabilities due to advanced DMX RDM technology and lots of user configuration options, the 3644PWM-EP will be undoubtedly be one of your best choices to drive CV LEDs -we're sure!Delivery without 3000P Startadressboard.4-channelDMX512/1990, DMX512A, DIN56930-2, ANSI E1-20 DMX RDMRDM Identify, password protection, HOLD-Level8 bit or 16 bit drive selectableOutput curve: quasi-logarithmic, linear or user-curve4 outresponse characteristics: direkt, smooth, slow, preciseVarious additional RDM functionsPower supply: 8...24VDC4 outputs 0...+8(24)VDC, max. 2AOutput frequency selectable from 244Hz to 15,6 kHzDimensions: 70mm x 70mm